ViaTalk is getting truck load of new consumers these days due to the brust of SunRocket, To get your line activated sooner, signup with Viatalk under “Bring your own device” (BYOD) option. Use your Sunrocket Innomedia Gizmo and signup with ViaTalk and get your line activated almost immediatly. Don’t forgot to port your SunRocket Number to new provider.
Here I am providing the information about unlocking and provisioning instructions for the Sunrocket/Innomedia MTA6328-2re Gizmo device to work with Viatalk.
Hot Offer: If you use the BYOD option and signup with Viatalk, then they will waive all activation fees and shipping charges. As part of special offer ViaTalk will also Buyout the 3 month of SunRocket Contract, Hence you will get Free Activation, Free Shipping and 3 Free Months of Service.
Instructions on how to set up ViaTalk to you SunRocket Innomedia Gizmo with ViaTalk Service:
1) Disconnect your WAN port from the gizmo (i.e. no internet)
2) Open your browser and Go to http://192.168.251.1/Voice_adminPage.htm
3) Login using your admin password.
If you do not know the password, try USER: admin PASSWORD: 7UprUtew or username: admin password: IM_Yass@Sun
4) Turn off provisioning if you have not done this already.
To do this, go to NETWORK -> Provisioning setting. Uncheck the “Enable Provisioning” box and hit the “Save and Reboot” button. After rebooting, you may not be able to login to the admin account since the reboot will default to index.htm. Hit CANCEL, and go to http://192.168.251.1/Voice_adminPage.htm to login.
5) Go to VOIP -> SIP Proxy and enter these settings:
a) SIP Proxy - Enter exactly what was sent to your email from ViaTalk. Remove any white spaces at the end.
b) Check “Use Outbound Proxy” box
c) SIP Local Signaling Port: 5060
d) SIP Domain: vtnoc.com
e) Registration Expiration time: 60
f) Preferred Codecs List: PCMU/800 for the first Dropdown
g) Choose “NONE” for all others.
h) Click “Save” button.
6) Go to VOIP -> User Account.
a) Choose Line 1 from dropdown
b) User ID: Your 11-digit phone number from ViaTalk email (starting with country code 1, Example: 1-xxx-xxx-xxxx)
c) Password: From email
d) User Name: Same as User ID above 6(b)
e) Authentication ID:
f) Use Hot Phone Number: NO
g) Hot Phone Number:
h) Use T38 FAX: Yes
i) Click “Save” button
Reboot your cable/dsl modem, then reboot your gizmo, and power-cycle your phone (if it is a powered phone).
You can verify this by going under the “information” to see if line 1 is registered.
With these easy 6 steps you are ready to connect to the world again !!
Related: Unlock the SunRocket Gizmo and Use it with JoiPhone VOIP
Hi Kishore,
I followed the instructions and installed Viatalk last night and it worked fine. In the interim, I also signed up for teleblend to “protect” my sunrocket phone number. All this I did yesterday night. This morning whenever I make calls from my phone , it was displaying my new viatalk number on the caller ID`s to whoever I was calling (which is what it was supposed to do). But suddenly ,since afternoon the gizmo stopped displaying the VOIP light and there was no dial tone. So I power cycled the gizmo and it took me back to the sunrocket settings and the called ID`s started showing my SR number.
I have two questions
1) Can I lock the SR gizmo to viatalk?
2) DO you think every time i powercylce the gizmo it will go back to old SR settings or is this only until I port my number to Viatalk?
PLs get back to me ASAP
Thanks
Arun
No, Power Cycle does not make an impact on your settings, might be some other reason or you have not saved the settings properly..
Give it an try again, it should work.
Thank You so much. I have a phone again!!!!
I have used your instructions, they work perfectly fine thanks for that. With ViaTalk second second phone port can also be used, do you know how to configure second phone port on the gizmo.
Thanks
Lats